STWYX15-225-900
Components:
- The uncoiler and its base
- Coil sheet guiding and adjusting equipment
- Film covered device
- Main roll forming system
- Post- Cutting device
- Hydraulic station
- PLC control System
- Support table
Material of Roll former system:
- Roller: High grade No. 45 forged steel, plated hard chromed on the surface of rollers with thickness 0.05mm.
- Active shaft material: High grade No. 45 carbon wrought steel at diameter 75mm.
- Cutting blade: Cr12 mould steel with quenched treatment.
Working flow:
Decoiling the sheet- - - Guiding the sheet- - - Covering the film- - - Roll forming- - - Measuring the length- - - Cutting the panel- - - Panels to the supporter.
Our machine's warranty time:
We offer 12 months quality grantee time starting from the date of delivery. When delivery, we will ship a set of wearing parts for free; Within the warranty period, maintenance of equipments and replacement of parts of equipment are charge-free.
After-sale service:
We offer sale after service for life. The machine will be inspected well in our workshop before delivery. We will send one technician to your factory to install the machine if you need extra installation, training service; The seller should arrange offer technical back-up and assign a technician people to the buyer's part.
| No. |       item | Parameter(all is subject to our final design) | |
| 1 Â |
Suitable raw material | Type | Common galvanized & pre-painted steel |
| Yield strength | 235MPa(or other high strength steel) | ||
| Thickness(mm) | 0.4-0.7 | ||
| width(mm) | According to final design | ||
| 2 | Manual uncoiler's capacity | Max.5tons | |
| 3 | Forming speed(m/min) | About 18-20m/min | |
| 4 | Main motor power(KW) | 7.5kw | |
| 5 | Hydraulic power(KW) | 3kw | |
| 6 | Forming roller groups | Around19-20 groups | |
| 7 | Raw material of forming roller | High quality No.45 steel | |
| 8 | Raw material of cutting blade | Cr12mould steel with quenched treatment | |
| 9 | controlling system | Mitsubishi PLC& converter | |
| 10 | Suitable industrial voltage |  According to your special requirement | |
| 11 | Machine dimensions(L*W*H) | 6.8m×1.8m×1.52m | |
| 12 | Machine weight | About 9-10tons | |
The Filter Press pump is summarized as a special pump specially used for the filling and feeding of the filter press.
In fact, the working principle of the filter press pump is very simple. The general principle is to adopt a unique hydraulic and impeller installation method.
When the filter press feeds, it can realize large flow and small flow according to the change of feed resistance of the filter press.
When using a filter press pump, there are many details that need to be paid attention to, ignoring one detail may lead to the scrapping of the entire filter press
1. Before starting the filter pump, inject liquid into the pump, close the valve at the outlet and turn on the power.
This step is to discharge the gas from the filter press pump, which is the same principle as other pumps, otherwise the pump will be full of other open filter press pumps, which will cause the pump to run dry and burn out.
2. After turning on the power, check whether the steering of the filter press pump is correct. Generally, the steering of the filter press pump is seldom fixed, so you need to check this problem when you run it.
3. The machine runs for 5 to 10 minutes for trial operation, and it runs normally when there is no abnormal phenomenon.
4. After the work is finished, when you are ready to close, first close the valve at the outlet, and then discuss disconnecting the power supply.
Filter Press Feed Pump,Slurry Pump For Water Filter,Filter Press Feed Pump Selection,Pump For Pneumatic Diaphragm
Shenzhen Hongfa Environmental Protection Equipment CO., LTD , https://www.hongfafilterpress.com