HOWO Refrigerated Truck 8T

Engine
Make and model----------------- WD615.62
Type--------- Diesel 4-stroke direct injection engine, 6-cylinder in-line with water cooling, turbo-charging & intercooling
Displacement---------------------9.726 liters
Maximum output------------------266 HP@ 2200 rpm ( 196KW @ 2200 rpm )
Max. Torque------------------------1100NM@1300-1600 rpm
Bore ---------126 mm
Stroke---------130 mm
Mean piston speed -----11.5 m/s
Compression ratio----------16: 1
Specific fuel consumption ----------197 g/kWh
Engine oil filling quantity ------------19 liters
Cooling system filling quantity ----------40 liters
Thermostat with 71 opening begin Rigid fan
Clutch
Model--------------------φ 420
Type -----------Single dry plate, compressed air assistant
Plate diameter----------; 420mm

Gearbox
Type--------FULLER 8JS100B
No. Of speeds--------8 forward, 1 reverse
Forward ratio---------11.4; 7.94; 5.63; 4.06; 2.81; 1.96; 1.39; 1.00
Reverse ratio---------11.35
Fuel tank capacity--------400L

Wheels and tires
Rim-------------------8.50-20
Tire ---------Triangle 11.00-20 /16
Quantity------------. 7

Brakes
Service brake-------Double circuit pneumatic brake
Parking brake-------- Spring-powered air-cut off brake
Assistant brake--------Engine exhaust brake

HOWO Cabin
All-steel forward control, 70° Hydraulically tiltable to the front, 3-arm windscreen wiper system with 3 speeds, laminate windscreen, with casted-in radio aerial,

Electric equipment
Operating voltage --------24 V, negative grounded
Starter^-----------24 V, 5.4 kW
Alternator--------28 V, 1500W
Battery voltage / capacitance------2x12V/165Ah
Cigar-lighter, horn, headlamp, fog light, reverse light
Front wheel alignment
Camber. ----1
Caster-------3
King pin inclination. ----------1
Toe-in(measured at the wheel diameter φ 648mm with cross-ply tyre) ---------3-4.5mm

Body dimension (length x width)^5900× 2260× 2200mm
Wheelbase---------4600+1350mm
Track
Front------2022mm
Rear------1830mm
Approach angle------. 18
Departure angle------17
Performance
Max. Driving speed...-----90 km/h
Turning circle diameter -----16m
Mass parameter
Kerb mass------9070Kg
Total mass-------19000Kg

Compressor
Model-------HT500 II
Voltage-----24V
Cooling material-----R404A
Cooling volume------4950W@0CO2600W@-20Co
Wind volume ----------2400m3/h
Colour--------------------Red/white


Front axle
Type. ----. Rigid stub axle with double T-cross members
Max. Load...6500Kg

Tandem axle
Type. -------------Pressed axle housing, single reduction with planetary wheel reduction
Ratio...4.8
Max. Load...13000Kg

Frame
Type...Parallel ladder with U-profiles and riveted cross members

Steering
Type...ZF8098
Ratio...26.2


Thanks a lot for paying our great attentions to our Company. I'm Levana from Sinotruk Qingdao Heavy Industry Co. Ltd
I would like to take this opportunity to introduce our company to you very briefly. Sinotruk Qingdao Heavy Industry Co. Ltd is one of the wholly owned subsidiaries of China National Heavy Duty Truck Corp., Ltd. It is one of the biggest special truck R&D, manufacturing and exporting base in China. A bountiful supply of spare parts, considerate after-sales services, abundant technical strength can provide timely and satisfaction service for the overseas users. Engine
Make and model----------------- WD615.62
Type--------- Diesel 4-stroke direct injection engine, 6-cylinder in-line with water cooling, turbo-charging & intercooling
Displacement---------------------9.726 liters
Maximum output------------------266 HP@ 2200 rpm ( 196KW @ 2200 rpm )
Max. Torque------------------------1100NM@1300-1600 rpm
Bore ---------126 mm
Stroke---------130 mm
Mean piston speed -----11.5 m/s
Compression ratio----------16: 1
Specific fuel consumption ----------197 g/kWh
Engine oil filling quantity ------------19 liters
Cooling system filling quantity ----------40 liters
Thermostat with 71 opening begin Rigid fan
Clutch
Model--------------------φ 420
Type -----------Single dry plate, compressed air assistant
Plate diameter----------; 420mm

Gearbox
Type--------FULLER 8JS100B
No. Of speeds--------8 forward, 1 reverse
Forward ratio---------11.4; 7.94; 5.63; 4.06; 2.81; 1.96; 1.39; 1.00
Reverse ratio---------11.35
Fuel tank capacity--------400L

Wheels and tires
Rim-------------------8.50-20
Tire ---------Triangle 11.00-20 /16
Quantity------------. 7

Brakes
Service brake-------Double circuit pneumatic brake
Parking brake-------- Spring-powered air-cut off brake
Assistant brake--------Engine exhaust brake

HOWO Cabin
All-steel forward control, 70° Hydraulically tiltable to the front, 3-arm windscreen wiper system with 3 speeds, laminate windscreen, with casted-in radio aerial,

Electric equipment
Operating voltage --------24 V, negative grounded
Starter^-----------24 V, 5.4 kW
Alternator--------28 V, 1500W
Battery voltage / capacitance------2x12V/165Ah
Cigar-lighter, horn, headlamp, fog light, reverse light
Front wheel alignment
Camber. ----1
Caster-------3
King pin inclination. ----------1
Toe-in(measured at the wheel diameter φ 648mm with cross-ply tyre) ---------3-4.5mm

Body dimension (length x width)^5900× 2260× 2200mm
Wheelbase---------4600+1350mm
Track
Front------2022mm
Rear------1830mm
Approach angle------. 18
Departure angle------17
Performance
Max. Driving speed...-----90 km/h
Turning circle diameter -----16m
Mass parameter
Kerb mass------9070Kg
Total mass-------19000Kg

Compressor
Model-------HT500 II
Voltage-----24V
Cooling material-----R404A
Cooling volume------4950W@0CO2600W@-20Co
Wind volume ----------2400m3/h
Colour--------------------Red/white


Front axle
Type. ----. Rigid stub axle with double T-cross members
Max. Load...6500Kg

Tandem axle
Type. -------------Pressed axle housing, single reduction with planetary wheel reduction
Ratio...4.8
Max. Load...13000Kg

Frame
Type...Parallel ladder with U-profiles and riveted cross members

Steering
Type...ZF8098
Ratio...26.2


Thanks a lot for paying our great attentions to our Company. I'm Levana from Sinotruk Qingdao Heavy Industry Co. Ltd
I would like to take this opportunity to introduce our company to you very briefly. Sinotruk Qingdao Heavy Industry Co. Ltd is one of the wholly owned subsidiaries of China National Heavy Duty Truck Corp., Ltd. It is one of the biggest special truck R&D, manufacturing and exporting base in China. A bountiful supply of spare parts, considerate after-sales services, abundant technical strength can provide timely and satisfaction service for the overseas users.

Other High Precision Small Parts Plastic Mould

Plastic molding and metal manufacturing manufacturer
Our metal manufacturing services include:
sheet metal manufacturing services.
injection mold tooling manufacturing, we can produce about 15 sets injection mold tooling per month, it is from small precision molds with tight tolerance to 10 ton large molds. Our company is especially good at double injeciton molding, unscrewing molds and over mold.
injection mold design services.Our design team have rich experience for injection mold design, and provide full 3D mold design services for global injection mold tooling manufacturers.
custom mold parts manufacturing. Our company provides metal manufacturing services, such as: CNC EDM Wire cut manufacturing, Cavity and core manufacturing of plastic injection molds, such as: cavity, core ,lifters and slides. If you need highly precise plastic molds components, are looking for a reliable manufacturing supplier to reduce costs, reduce lead times, improve quality and increase productivity, our manufacturing services is a good choice

OEM Precision Small Plastic Parts

DoHform Mold(China) Co,.Ltd. , https://www.dhform.com