1) Problems in selection. Some vortex sensors in the caliber selection or after the selection of the design due to changes in process conditions, making a large selection - a specification, the actual selection should choose the smallest possible diameter, in order to improve the measurement accuracy, mainly in this regard Questions 1, 3, and 6 are relevant. For example, a vortex street line is designed for use on several equipment. Because some of the equipment in the process is not used sometimes, the current actual use flow rate is reduced, and the actual use causes the original design selection aperture to be too large, which is equivalent to increase the measurable flow rate. The lower limit indicates that the flow rate can not be guaranteed when the flow rate is small in the process piping, and can also be used when the flow rate is large, because it is sometimes too difficult to remodel. Changes in process conditions are only temporary. The re-tuning of the parameters can be combined to improve the indication accuracy.
2) Installation issues. The main reason is that the length of the straight pipe section in front of the sensor is not enough, which affects the measurement accuracy. The reason for this is mainly related to Problem 1. For example, the straight pipe section in front of the sensor is obviously insufficient. Because the FIC203 is not used for metering, it is only used for control. Therefore, the current accuracy can be equivalent to degraded.
3) The reason for the parameter setting direction. Due to a wrong parameter, the instrument indicates an error. The parameter error causes the secondary instrument full-scale frequency to be calculated incorrectly. The reasons for this are mainly related to problems 1 and 3. Full-scale frequency is similar to the indicator that the long-term inaccurate, the full-scale frequency of the actual full-scale calculation of the full-scale frequency indicates that a wide range of fluctuations, can not read, and the inconsistency of the parameters on the data has affected the final determination of the parameters, and finally passed The recalibration combined with each other determines the parameters and solves this problem.
4) Secondary instrument failure. This part of the more failures, including: an instrument board circuit is broken, the range setting has a bit of individual display is bad, K coefficient is set to display a bad individual bits, making it impossible to determine the range setting and K-factor setting, which Some of the reasons are mainly related to questions 1 and 2. By fixing the corresponding fault, the problem is solved.
5) Four-way line connection problem. The circuit is well connected on the surface of some loops. Carefully check that some of the connectors have actually been loosened and the loop is interrupted. Although some connectors are tightly connected, the fastening screws are fastened to the cable sheath due to the problem of the secondary cables. Interruption, this part of the reason is mainly related to question 2.
6) The connection between the secondary instrument and the subsequent instrument. Due to problems with subsequent instruments or due to subsequent instrument overhaul, the mA output circuit of the secondary instrument is interrupted. For this type of secondary instrument, this part is mainly related to Problem 2. Especially for the follow-up recorder, in the case of long-term damage to the recorder can not be repaired, we must pay attention to the output of the secondary short-circuit meter.
7) The loop has no indication due to the failure of the secondary meter flat cable. Due to the long-term operation, coupled with the impact of dust, causing flat cable failure, by cleaning or replacing the flat shaft wire, the problem can be solved.
8) For problem 7 is mainly due to the fact that the secondary instrument shows that the head coil fixing screw is loose, causing the meter head to sink, the pointer and the case to have large friction, and the action is not working. By adjusting the meter head and fixing again, the problem is solved accordingly.
9) Use environmental issues. Especially in the sensor part installed in the well, due to the high humidity in the environment, the board is damp, which is partly related to problems 2 and 2. Through corresponding technical reform measures, the part of the sensor with a large environmental humidity was re-disposed of the probe part and the conversion part, and a separate sensor was used. Therefore, the working environment was good, and this part of the instrument was working well the other day.
10), due to poor on-site adjustment, or due to the actual changes after adjustment. Due to live vibration and noise balance adjustment and sensitivity adjustment is not good. Or, due to the re-alteration of the on-site situation after a period of time after the adjustment, the indication problem is caused. This part of the reason is mainly related to questions 4 and 5. Use the oscilloscope, combined with the operation of the process, readjust.
Ladle Shroud
Ladle shrouds are applied to connect ladles to tundish. They stabilize molten-steel streams and protect molten steel from splashing and being oxidized. Ladle shrouds feature superior thermal shock resistance, slag erosion resistance and wear resistance, etc. They are easy to be installed and free of preheating, which will greatly improve the working conditions and being widely spreaded.
Anyang Jinrong Company is a professional manufacturer of refractory materials,mainly produce Zirconia Insert , Zirconia Tundish Nozzle ,Tundish Upper Nozzle,Tundish Lower Nozzle,Tundish Well Block,Submerged Entry Nozzle,Ladle Nozzle,Ladle Upper Nozzle , Ladle Lower Nozzle, Ladle Slide Gate Plate,Porous Plug.Over the past 28 years, our company have become a leading refractory manufacturer at home and abroad.
Perfect business philosophy and strong production equipment, make the company become stronger.All the staff have established the ANYANG JINRONG brand with the supremacy of integrity,excellent quality and service, made outstanding contributions to the development of iron and steel industry in China and even in the word .
Ladle Shroud,Ladle Shroud For Sale,Ladle Shroud Manipulator,Alumina-Graphite Ladle Shroud
ANYANG JINRONG METALLURGICAL MATERIALS CO.,LTD , https://www.ladlenozzle.com